Tag: Four

Stainless Steel Kitchen Sinks – Four Things You Must Know Before Buying a Stainless Steel Sink

I was recently approached with a question about stainless steel sinks. A customer of mine searched online for a 33″ stainless steel sink. The results ranged from $ 98.00 to $ 1,700.00 so of course the question came up about what the difference was. So was born the four things you must know before buying a stainless steel sink.

Start with the gauge of the sink. The gauge is the thickness of the steel, the smaller the number the thicker the steel. Most kitchen sink manufacturers produce stainless steel sinks from 22 gauge to 16 gauge. The thicker steel will cost you more all things being equal. The reason you might want a thicker steel sink is it is more resistant to dents.

Next you’ll want to know what type of sound insulation is used on the sink. The sound insulation serves one purpose, to reduce or eliminate the ringing that follows after you toss something into the sink.

With out any sound insulation your sink will sound like a bell. The most common type is a sprayed textured coating on the back side of the sink. You may also see a sound dampening pad under the spray coating; this is a very effective sound deadening combination. You can hit this type of sink with a hammer and hear little more than a thud. Both types are fine, just be sure you have some form of sound insulation.

One of the least considered aspects of a sink is the grade of stainless steel. Like most metals, stainless steel is broken up into many different grades with different properties. In my research I have found that most stainless steel sinks are one of four grades, 201, 301, 302, 304. A grade 201 sink is most often seen in the big home improvement stores on the lowest end of the price scale.

As of this writing I have found them as low as $ 90.00 for a 33″ undermount. Grade 302 is most often used for utensils. As you progress into the higher grades, the steel becomes more corrosion, oxidation, and rust resistant. The sinks ability to stay shiny and new is what this comes down to. I would suggest purchasing a sink made of 302 or 304 stainless steel.

Finally we come to design, of course, this is where most of us would start our search for a new sink, but I’ve left this for last because it will affect the price of the sink more than any other single aspect we’ve covered. Looking at sink design today you can’t help but be amazed at the creativity and innovation that exists. The only real advice I can give concerning design is be sure your counter top fabricator can cut the shape of the sink and that your plumber is aware of the type of installation before the counter top is installed.

John S. Gelfusa CGR is the president of HomeWorks cgo inc.

For articles about kitchen remodeling Visit my website The Smart Way To Remodel.com

Click here for more information about Kitchen Remodeling Michigan.

 

Bookmark and Share
Tags : , , , , , , , , , ,

Four Common Types Of Faucet When Considering a Change

If you own a house, there comes a time you should replace the faucet of your shower and tub when it gets old and does not function properly. However, since faucet is not a thing needing changing frequently, we often do not know what to do exactly. Fortunately, if you know in hand types of faucet to choose, then changing it is just quite simple.

 

When shopping for your new faucets, you will see these four common types of faucets. It’s helpful to know a little about each one so that you can make an informed decision as to which one to get.

Cartridge – These have a rather distinct look them to them as the knob used to release and stop water move up and down. Contrast this to the traditional ones that use knobs, which you have to turn left and right.

To control the flow of water, these faucets have a movable cartridge within the stem. These don’t require lots of maintenance and last a long time because there are less movable parts.

Compression – These are the oldest and most common types of valves. They have a stem held in place with a plastic or rubber washer, which nests into a metal (typically brass) seat. As you turn the knob left, the stem rises and allows water to flow. As you turn the knob right, the stem lowers and pushes the washer into the seat, stopping water flow. These faucets are inexpensive, and there’s a reason for it. The washers often wear out and this causes leaks. They can be quick to repair, but special tools are required.

Ball Valve – These types of faucets are usually a one-handle setup.

There is a ball with slots, one for hot water and one for cold water, inside the stem. As the handle is turned, water flows through these slots. Controlling the temperature is the result of how much hot and cold water flows from each slot as the handle is turned clockwise and counterclockwise. Water pressure is controlled with the up and down movement of the handle. These are very durable as they don’t require washers to operate.

Ceramic Disc – These faucets have two ceramic discs inside the stem, one on top the other. When the faucet is turned all the way clockwise, the two discs are forced together, creating a water tight seal. When the faucet is turned counterclockwise the top disc rises, allowing water to flow. Ceramic disc faucets are preferred by many experts industry as they are highly durable due to the lack of moving parts and ceramic’s ability to resist wear, tear, and erosion.

 

 

There are many variations of the above mentioned faucet categories. However, one of the most beautiful kind are oil rubbed bronze bathroom faucet assemblies. You won’t regret getting one. To learn more, visit http://oilrubbedbronzebathroomfaucet.org.

Bookmark and Share
Tags : , , , , ,